Nokia Asha 306 Insert Sim IC Solution Jumper Problem Ways

Nokia Asha 306 Insert Sim IC Solution Jumper Problem Ways

in case of insert sim problem in Nokia Asha 306 it will show insert sim, sim not valid, and may not show signal.to solve Nokia Asha 306 Insert Sim IC Solution Jumper Problem Ways we have to do a few simple steps as given in this post.in first step replace you sim and try it.scratch sim points in mobile slightly then try.
Nokia Asha 306 Insert Sim IC Solution Jumper Problem Ways
after dis assembly check all sim jack points at mother board with meter.check all these parts and track that are given in above diagram and if any of them is missing apply jumpers to make that path in good condition.if any of the components is missing replace it with new.

you can change sim ic also and may can apply jumpers after removing ic from mother board.there are some posts also to describe that how to make jumpers in sim ic to solve insert sim problem.

For more information and new tips and tricks about this problem solution keep visiting this page we will update it if there will be new updates.some related post are also given below you can read more about mobile phone.

Please note that although every diagram & solution posted on our website has been tested by one or more members of our team before posting,so we will not be responsible for any loss or damage, including personal injury.Use this repair solutions at your own risk.

Nokia Asha 306,Nokia,Insert Sim,Sim,Solution,Jumper,Problem,Ways

Nokia Asha 306 Insert Sim IC Solution Jumper Problem Ways Sim Not Working Sim Not Valid

Nokia Asha 306,Nokia,Insert Sim,Sim,Insert Sim Problem,Insert Sim Solution,Insert Sim Jumpers,Insert Sim Ways

Samsung S8500 Wave Signal Network Problem Solution Jumpers

Samsung S8500 Wave Signal Network Problem Solution Jumpers Here bellow is the Samsung hardware repair solution I9070i no signal, In the case described above her that there is no network / signal on Samsung S8500 Wave caused by his excess stress on the point that produced RF ICs By VCO, in his Normal Voltage which released 0,5V By VCO range – 1.34V, measuring results generated at the measuring point which you can see in the picture with the top yellow box marking is 4V,
Samsung S8500 Wave Signal Network Problem Solution Jumpers
it means the voltage that produced too large, causing damage to the signal Samsung S8500 Wave. Process Improvement In his Samsung S8500 Wave, Please do the replacement of the component in the given marking Yellow. ‘s only one 1 sample Causes and Many More causes damage Samsung S8500 Wave signal if the measurement result is the same as the picture above then please you to do the replacement the IC is given a yellow marking. thank you

Samsung Galaxy S5 G900F Speaker Solution Jumper Problem Ways Earpeace

Samsung Galaxy S5 G900F Speaker Solution Jumper Problem Ways Earpeace

if we have a speaker problem in Samsung Galaxy S5 G900F we will not be able to hear voice of call.we can temporary solve this issu by using Loud Speaker but to fix this problem we have to do a few basic diagnostics and steps to solve Samsung Galaxy S5 G900F Speaker Solution Jumper Problem Ways Earpeace.
Samsung Galaxy S5 G900F Speaker Solution Jumper Problem Ways Earpeace
Open Mobile and check speaker points with a meter if they do not show continuty then speaker is dead and if they show a good value chak speaker attachement prints on board do they have value also then change speaker with new one.if speaker changing can not solve this issue check all these parts and track that used in speaker function in Samsung Galaxy S5 G900F.

All parts components and tracks can be found in diagram above so check these components and also clean near by area of these parts.dry it with hot air and ceck all tracks with meter if missing apply jumpers and you may can change resold or replace these parts one by one till you solve Samsung Galaxy S5 G900F Speaker Solution Jumper Problem Ways Earpeace

For more information and new tips and tricks about this problem solution keep visiting this page we will update it if there will be new updates.some related post are also given below you can read more about mobile phone.

Please note that although every diagram & solution posted on our website has been tested by one or more members of our team before posting,so we will not be responsible for any loss or damage, including personal injury.Use this repair solutions at your own risk.

Samsung Galaxy S5 G900F,Nokia,Speaker ,Earpeace,Solution,Jumper,Problem,Ways

Samsung Galaxy S5 G900F Speaker Solution Jumper Problem Ways Speaker Not Working Earpeace

Samsung Galaxy S5 G900F,Nokia,Speaker,Earpeace,Speaker Problem,Speaker Solution,Speaker Jumpers,Speaker Ways

Samsung Galaxy S5 G900F ear speaker solution
Samsung Galaxy S5 G900F ringer not working solution, how to work Samsung Galaxy S5 G900F ringer
orginal Samsung Galaxy S5 G900F ear spker not working solution
Samsung Galaxy S5 G900F not work ear spker

Samsung Galaxy Clone i9277 how dead boot repairing solution 100% done

Samsung Galaxy Clone i9277 how dead boot repairing solution 100% done

Little Guide :
What is it ?
in MTK Android there is many Partitions in your phone. like Preloader, Recovery, Bootimg etc….. if somehow Preloader get Corrupted then you phone will not able to DETECT WITH PC !!! in other words you will have phone with BOOT DEAD.
Samsung Galaxy Clone i9277 how dead boot repairing solution 100 done
How Preloader get corrupted ?
There could be few reasons but main reason could be that someone or you Flash your complete phone (include Preloader) with wrong files or with wrong ver. Also there could be reason someone Delete Preloader or you Deleted.
How could i know my phone have preloader dead ?
Preloader can be dead if some one Flash it wrong and after flash your mobile will not detect with pc any more. for confirm
open device manager
take battery out from phone
insert usb
insert battery
and check is computer detecting any device
If it’s not detect then you have phone which Preloader is dead AKA Boot Dead
How can i repair it ?
you have to disassemble your phone and take pcb out. check there should be some Golden points. check these points there should be written on them Rx,Tx,GND,Vcc,Vcharge etc… check there should be written “COLO” or “KOLO” or “KCOLO” you have to Sold that point with GND After Sold Attach usb now your phone will detect with USB !! and now ready to Flash.
In some phones “COLO” or “KOLO” or “KCOLO” not written for those type of phones you have to test all points one by one Short Golden point with GND and attach usb cable which point short with gnd can able to detect your phone by pc is Force Preloader Mode Test Point !! Keep in mind Don’t Short Vcc,Vcharge or any other pin which have 4.x Volts also i had tested “Colo” or “Kolo” or “KCOLO” don’t have any kind of volts..
So Please share your Researched Force Preloader mode TestPoint Picture with Model name